Tools

Slim-Tip Insulated Screwdriver Set sizes: 4-Inch round shank in a #2 Phillips and a 1/4-Inch Cabinet tip1000-Volt rated insulated screwdrivers with slim-tips that allow for greater access into tight spacesLayer of orange impact and flame-resistant...

Multi-bit screwdriver includes 13 different screwdriver bits and a 1/4-Inch nut driverIndustrial-strength bits that are conveniently housed in the handleAdjust the length of the blade for easier accessImpact rated blade can be removed for use as an...

Step Drill Bit has 2 spiral flutes to remove chips and help pull the bit through material for faster cuttingTitanium nitride coating dissipates heat for longer bit life1/4-Inch hex shank for firm, positive grip in impact driver and standard drillSplit...

This Klein Screwdriver / Nut Driver allows for one-handed driving, with seven sizes in one toolStrong, Rare-Earth magnets (1/4-Inch, 5/16-Inch, 11/32-Inch, 3/8-Inch, 1/2-Inch) securely hold nuts and boltsSpring coil (7/16-Inch, 9/16-Inch) holds nuts and...

Non-magnetic design. ¼" hexagon, suitable for holders as per DIN ISO 1173-F 6.3.

Opening and closing Click Clamps does not require a special skill; it requires a special tool. No need to replace the OEM clamp with a screw clamp, these pliers will not harm the clamps they are compressing, allowing them to be reused over and over again...

Reversible ratchet for 1/2" socketsQuick, easy and reliable locking of attached socketsReversible for clockwise and counterclockwise directionsExtremely smooth action1000V plastic dipped

Crimping die for Harting/Suhner connectors for fiber opticsCapacity - SW- 5/32", 11/64" and 3/16" (3.8, 4.3, 4.95 mm) and sleeve capacity -11/16", 13/64" and 15/64" (4.5, 5.2 and 6.0 mm)

Precision pliers for ultra fine cutting work in electronics and fine mechanicsGround, very sharp cutting edges without bevel for flush cutting perfect for cable tiesPrecision shaped tips cut wires resting on a board from 1/64" (0.2 mm) diameterJoint...

T handle provides easier access to hard to reach areas and better gripFor widths across the flats at 5 mm1000V plastic dippedSpecial tool steel; oil-hardened

For fine cutting work in electronics and fine mechanicsSturdy, zero-backlash box jointLow friction double spring for gentle and even openingThe mirror polish together with a fine film of oil offer effective rust protection - no circuit faults caused by...

T handle provides easier access to hard to reach areas and better gripFor widths across the flats at 8 mm1000V plastic dippedSpecial tool steel; oil-hardened

20% less effort required compared to conventional diagonal cutters of the same lengthForged-on axle for heavy-duty workFor very tough, continuous useHigh cutting performance with minimum effort due to optimum coordination of the cutting edge angle and...

Includes 1 each of: Screw Extractor Double Edged Size 1 (9R 471 001 3), Screw Extractor Double Edged Size 2 (9R 471 002 3), Screw Extractor Double Edged Size 3 (9R 471 003 3)

Locator for 97 49 66 Solar connector MC4

T handle provides easier access to hard to reach areas and better gripFor widths across the flats at 22 mm1000V plastic dippedSpecial tool steel; oil-hardened

Locator for 97 49 65 Solar connector MC3

High leverage cutting edges for cutting soft, hard and piano wireHigh cutting capacity with minimal effort due to optimum coordination of cutting edge angle and transmission ratioCutting edge hardness (approx. 64 HRC)Cutting capacity - up to 5/32" for...

Offset design for easier access and allows for vertical positioning over bolt headFor widths across the flats at 24 mm1000V plastic dippedChrome plated chrome vanadium steel; forged, oil-hardenedFor widths across the flats at 3/4"