Cutters, Crimpers & Strippers

Cleanly cuts copper and aluminum cables, single and multiple wire without crushing or deformation25 degree comfort angle for a more ergonomic working positionCuts soft wire up to 2/0 AWGNot suitable for steel wire, ACSR, or hard drawn copper conductors

For fine cutting work in electronics and fine mechanicsSturdy, zero-backlash box jointLow friction double spring for gentle and even openingThe mirror polish together with a fine film of oil offer effective rust protection - no circuit faults caused by...

High leverage cutting edges for cutting soft, hard and piano wireHigh cutting capacity with minimal effort due to optimum coordination of cutting edge angle and transmission ratioCutting edge hardness (approx. 64 HRC)Cutting capacity - up to 13/64" for...

25 degree angled diagonal cuttersApproved ergonomics with power jointExtra long precision cutting edgeFor tough, continuous useHigh leverage design for 30% more cutting powerInduction hardened cutting edges cut any copper, aluminum, hard wire, piano...

High leverage cutting edges for cutting soft, hard and piano wireHigh cutting capacity with minimal effort due to optimum coordination of cutting edge angle and transmission ratioCutting edge hardness (approx. 64 HRC)Cutting capacity - up to 5/32" for...

Specifically designed for cutting Kevlar in optical fiber cable, not recommended for other materialBlade is 4 5/16" in lengthPrecision ground blades with serration prevent the fibers from slipping and guarantees a clean cutRiveted precision joint, for...

20% less effort required compared to conventional diagonal cutters of the same lengthForged-on axle for heavy-duty workFor very tough, continuous useHigh cutting performance with minimum effort due to optimum coordination of the cutting edge angle and...

Cable shears with adjustable telescopic handles allow angular positioningFor cutting cables up to 1 1/2" (38 mm) in diameter, handles can be positioned at an angle to set the optimum handle width, great for work in confined areasLightweight tool for...

Crimping dies for solar cable connectors (Huber + Suhner) 4.0 + 6.0 mm²Capacity - 4.0, 6.0 mm² and 12, 10 AWG

For fine cutting work in electronics and fine mechanicsSturdy, zero-backlash box jointLow friction double spring for gentle and even openingThe mirror polish together with a fine film of oil offer effective rust protection - no circuit faults caused by...

High leverage cutting edges for cutting soft, hard and piano wireHigh cutting capacity with minimal effort due to optimum coordination of cutting edge angle and transmission ratioCutting edge hardness (approx. 64 HRC)Cutting capacity - up to 13/64" for...

The 5 1/2" version is for greater stability and cutting performancePrecision ground cutting edges without bevel for flush cutting the finest of wires e.g. in electronics and precision engineeringPrecisely shaped tips also cut adjacent wires from 1/64"...

20% less effort required compared to conventional diagonal cutters of the same lengthForged-on axle for heavy-duty workFor very tough, continuous useHigh cutting performance with minimum effort due to optimum coordination of the cutting edge angle and...

Crimping die for Solar connectors - WeilandCapacity -1.5 to 2.5 mm²

For fine cutting work in electronics and fine mechanicsSturdy, zero-backlash box jointLow friction double spring for gentle and even openingThe mirror polish together with a fine film of oil offer effective rust protection - no circuit faults caused by...

Forged-on axle for heavy duty cuttingPrecision cutting edges for soft, hard and piano wireCuts thick wires with less effort than other diagonal cutters of the same lengthCutting edges are in the center of the cutter headHigh cutting performance with...

For cutting cardboard, plastics, aluminum, brass and copper foilsNot suitable for steel wire or iron sheetsPrecision ground, hardened bladesPinch guard prevents operators´ fingers being pinchedAdjustable bolted jointWith opening spring and locking...

For cutting cardboard, plastics, aluminum, brass and copper foilsNot suitable for steel wire or iron sheetsPrecision ground, hardened bladesPinch guard prevents operators´ fingers being pinchedAdjustable bolted joint40˚ angled head - for easy execution...

For cutting composite pipes with diameters of 1/2" to 1" and for cutting flexible corrugated pipes with diameters of 3/4" to 1 3/8"Features an opening spring and locking leverReplaceable blades - part number 90 29 01 (composite pipes) or 90 29 02...

High cutting performance with minimum effort due to optimum coordination of the cutting edge angle and transmission ratioCutting capacity of steel up to 48 HRCRobust cutting edges with a hardness of (approx. 62 HRC)Forged-on stopper with comfortable...